EC670 Keypad instructions

EC670 Keypad instructions


The EC670 Keypad is used to arm and disarm the tracking system (Subject to subscription activation)

Operating the system

To arm the system simply key in your 4 digit code and press the ON key, the keypad should issue a single beep. To disarm the system key in your 4 digit code and press the OFF key, the keypad will issue two beeps. If an error is made i.e. inputting an incorrect code then multiple beeps will be sounded.
NOTE: If the wrong code is entered 5 times then the keypad will beep 5 times and lockout for 10 minutes.

Changing the code

When your caravan is first delivered the default code is set to 1234, this should be changed as soon as possible to a 4 digit code of your choice. To change the code please follow the steps below:
  1. From a disarmed state:
    1. Press and hold the ON key for 5 seconds until you hear a long beep then immediately stop pressing the ON key, the long beep indicates that you are in programming mode.
    2. Enter the old code and press the OFF key, a beep will be issued.
    3. Then enter your new code and press the OFF key again a beep will be issued.
    4. Confirm the new code by entering it a second time and again press the OFF a beep again will be issued and will exit the programming menu.
    5. If no keys are pressed within 10 seconds the system will exit the programming mode. If a mistake is made when in the programming mode then a number of beeps will be issued to advise of the error, this will then exit the programming mode.

Beep codes

1 beep arm 
2 beeps disarm
3 beeps incorrect code has been entered
4 beeps error
5 beeps time out
1 long beep in listen mode
Note: Each key press will also beep to inform you the key has been pressed.

Recovering a lost code

In the event of the loss of the code then the following process shall be used.
  1. Press and hold the OFF key for 5 seconds until you hear a long beep then immediately stop pressing the OFF key, the long beep indicates that you are in reset mode.
    1. Following the long beep, a series of short sounds (the beep code) will be issued in the form of 4 codes (these will consist of 1 to 4 beeps) note down the number of beeps.
    2. Call Sargent Technical support 01482 678981, please ensure that you have your caravan details to hand as a security check will be undertaken to verify that you are the registered owner.
    3. Following the issue of the reset code from Sargent Technical then re-enter the reset mode, after the beep code has ended then enter the code given by Sargent Technical and press the ON key, a confirmation beep will sound. The code has now been reset to 1234, again it is recommended to change this to a code of your choice.
    4. If a mistake is made when in the reset mode then a number of beeps will be issued to advise of the error, this will then exit the reset mode.

    • Related Articles

    • SWIFT - Swift Command - Tracking Information

      Swift Command Account Why do I need an account? You need a Swift Command account to take advantage of the Swift Command features like remote alerts, remote levels and remote control. You also need an account if you wish to add a tracking ...

    • Calibrate the EC480 battery amps

      The EC480 (or EC300) control panel, connected to the EC500 PSU has the ability to measure and display the current (A) going into or out of the active (Selected) battery. Positive Current (+) indicates charging of the battery whilst Negative Current ...

    • The battery current reading seems incorrect on my EC325 / EC328 / EC300 control panel.

      If the battery current reading seems incorrect on any of the listed control panels, you may need to calibrate the current sensor in the PSU to the control panel in order to get a true reading. All of the above panels share the same layout and menu, ...

    • SWIFT - Swift Command - Connectivity Issues

      Bluetooth and Remote Features Is my device compatible? Your device must support Bluetooth 4 (or Bluetooth Low Energy BLE) standard. If you are unsure, there are apps available to check Bluetooth connectivity and compatibility. LightBlue® — Bluetooth ...

    • My AS350 keyfob will not arm my alarm

      There are a few simple checks to make before trying to learn your keyfob. Are you close enough to your caravan? The range of the keyfobs is 6M, try moving closer. Does the torch work?  If not, the battery may be discharged and need replacing. If the ...